IA machine install: Difference between revisions
add ia install content |
add ia install content |
||
| Line 10: | Line 10: | ||
Getting Started | == Getting Started == | ||
# Make sure the LBPayLinker model Type. See picture. | |||
{| class="wikitable" | |||
|+ | |||
![[File:1000030570.png|center|thumb]]NYJ31 | |||
![[File:1000030589.png|center|thumb]]A1 | |||
|} | |||
2. Check LBPayLinker parts. | |||
* For model NYJ31 - antenna and machine wiring cable | |||
* For model A1 - interface cable and machine wiring cable | |||
{| class="wikitable" | |||
|+ | |||
![[File:Ia device parts.jpg|center|thumb]]NYJ31 | |||
![[File:A1 ia device parts.jpg|center|thumb]]A1 | |||
|} | |||
3. Connect the interface cable on the device. | |||
{| class="wikitable" | |||
|+ | |||
![[File:Ia device connection.jpg|center|thumb]]NYJ31 | |||
![[File:A1 ia connection.jpg|center|thumb|486x486px]]A1 | |||
|} | |||
4. Open IA machine cover. | |||
{| class="wikitable" | |||
|+ | |||
!open board cover | |||
!open top cover | |||
!open coindrop cover | |||
|} | |||
5. Locate power connector and disconnect it to shutdown the machine. | |||
6. Locate coindrop interface cable to machine board. | |||
(1) Coindrop power to board | |||
[[File:Ia coindrop cable.jpg|center|thumb|450x450px]] | |||
(2) Coindrop signal to board | |||
[[File:Ia signal cable.jpg|center|thumb|450x450px]] | |||
7. Locate LBPayLinker machine wiring cable. | |||
[[File:Ia interface cable.jpg|center|thumb|447x447px]] | |||
8. Connect machine wiring cable BC type to coindrop - board cable. | |||
(1) Disconnect coindrop power to board cable and loop with LBPayLinker wiring cable. | |||
(2) Disconnect coindrop signal to board cable and loop with LBPayLinker wiring cable. There are 2 signal pair, yellow-white and red-black. Use red-black signal pair. | |||
9. Connect machine power source connector to the board. | |||
Revision as of 22:47, 18 April 2026
Pre-requisites
- Open machine cover
- Type of LBPayLinker devices (Model NYJ or A1)
- Type of LBPayLinker wiring cable (BC, IA or TOSEI)
IA Machine
Getting Started
- Make sure the LBPayLinker model Type. See picture.
 |
 |
|---|
2. Check LBPayLinker parts.
- For model NYJ31 - antenna and machine wiring cable
- For model A1 - interface cable and machine wiring cable
 |
 |
|---|
3. Connect the interface cable on the device.
 |
 |
|---|
4. Open IA machine cover.
| open board cover | open top cover | open coindrop cover |
|---|
5. Locate power connector and disconnect it to shutdown the machine.
6. Locate coindrop interface cable to machine board.
(1) Coindrop power to board
(2) Coindrop signal to board
7. Locate LBPayLinker machine wiring cable.
8. Connect machine wiring cable BC type to coindrop - board cable.
(1) Disconnect coindrop power to board cable and loop with LBPayLinker wiring cable.
(2) Disconnect coindrop signal to board cable and loop with LBPayLinker wiring cable. There are 2 signal pair, yellow-white and red-black. Use red-black signal pair.
9. Connect machine power source connector to the board.