BC machine (washer and dryer) install: Difference between revisions
Add bc content |
No edit summary |
||
| (11 intermediate revisions by the same user not shown) | |||
| Line 31: | Line 31: | ||
3. Connect the interface cable on the device. | 3. Connect the interface cable on the device. | ||
[[File:Connect bc | [[File:Connect bc standard.jpg|center|thumb|631x631px|* for device NYJ31 connect wifi antenna cable and machine wiring cable as picture above.]] | ||
[[File:Connect bc a1 touch.jpg|center|thumb|646x646px|* for device A1 connect interface cable and machine wiring cable as picture above]] | |||
* for device NYJ31 connect wifi antenna cable and machine wiring cable as picture above. | |||
]] | |||
[[File:Connect bc a1.jpg|center|thumb|646x646px| | |||
* for device A1 connect interface cable and machine wiring cable as picture above | |||
]] | |||
| Line 51: | Line 43: | ||
![[File:Wiring bc dryer.jpg|thumb]]open coindrop cover | ![[File:Wiring bc dryer.jpg|thumb]]open coindrop cover | ||
|} | |} | ||
5. Locate power connector and disconnect it to shutdown the machine. | 5. Locate power connector and disconnect it to shutdown the machine. | ||
[[File:Disconnect power bc.jpg|center|thumb]] | |||
6. Locate coindrop interface cable to machine board. | |||
(1) Coindrop power to board | |||
(2) Coindrop signal to board[[File:Bc coindrop-board cable resize.jpg|center|thumb|506x506px]] | |||
7. Locate LBPayLinker machine wiring cable. | |||
[[File:Bc cable wiring.jpg|center|thumb|381x381px]] | |||
8. Connect machine wiring cable BC type to coindrop - board cable. | |||
(1) Disconnect coindrop power to board cable and loop with LBPayLinker wiring cable. | |||
[[File:Bc power coindrop.jpg|center|thumb]] | |||
(2) Disconnect coindrop signal to board cable and loop with LBPayLinker wiring cable. There are 2 signal pair, yellow-white and red-black. Use red-black signal pair. | |||
[[File:Bc signal coindrop.jpg|center|thumb]] | |||
9. Connect machine power source connector to the board. | |||
[[File:Connect power source.jpg|center|thumb]]10. After the device done installation, next step is to configure the device. [[Configure device using admin app]] | |||
== Installation video == | |||
Installation steps video.  | |||
https://lbunlimitedwash.com/lbwiki/video/BC_Device_installation.mp4 | |||
Latest revision as of 00:36, 27 April 2026
Pre-requisites
- Open machine cover
- Type of LBPayLinker devices (Model NYJ or A1)
- Type of LBPayLinker wiring cable (BC, IA or TOSEI)
BC Machine
This is the washer and dryer type of machine.
Getting Started
- Make sure the LBPayLinker model Type. See picture.
 |
 |
|---|
2. Check LBPayLinker parts.
- For model NYJ31 - antenna and machine wiring cable
- For model A1 - interface cable and machine wiring cable
 |
 |
|---|
3. Connect the interface cable on the device.
4. Open BC machine cover.
 |
 |
 |
|---|
5. Locate power connector and disconnect it to shutdown the machine.
6. Locate coindrop interface cable to machine board.
(1) Coindrop power to board
(2) Coindrop signal to board
7. Locate LBPayLinker machine wiring cable.
8. Connect machine wiring cable BC type to coindrop - board cable.
(1) Disconnect coindrop power to board cable and loop with LBPayLinker wiring cable.
(2) Disconnect coindrop signal to board cable and loop with LBPayLinker wiring cable. There are 2 signal pair, yellow-white and red-black. Use red-black signal pair.
9. Connect machine power source connector to the board.
10. After the device done installation, next step is to configure the device. Configure device using admin app
Installation video
Installation steps video. 
https://lbunlimitedwash.com/lbwiki/video/BC_Device_installation.mp4